第一，就是加工的环境，精密平面磨床同一工作场地附近是不可能放置诸如冲床，Q420C高强板车床等震动较大的机床，容易引起共震，如何判断是否有共振？停掉磨床，开动冲床或车床，如果手去触摸磨床有震动或麻手感觉就是影响到了。所以必须要分开车间放置。

First, is the processing environment, near the same precision surface grinder work site is impossible to place such as punching machine, Q420C high strength plate lathe machine vibration, easy to cause a total shock, how to judge whether there is a resonance? Stop the grinding machine, start the punch or lathe, if the hand to touch the grinder with vibration or hemp hand feeling is affected. So it is necessary to separate the workshop.

第二，检查地面，如果机床地脚螺丝水平没调好，就会引起机床的共振。因为有时加工场地地面平整度不是很好，所以要通过调节水平螺丝来让机床达到一个平整的高度。通过拧紧地脚螺丝，让所有的地脚螺丝都紧贴着实地。

Second, check the ground, if not adjusted the level of machine screws, it will cause the resonance of machine tool. Because sometimes the surface roughness of the processing site is not very good, so to adjust the level of screws to allow the machine to achieve a level of height. By tightening the anchor bolts, anchor bolts for all are close to the field.

第三，如果上述动作做完后，震动仍未消除，就应检查是否由于地面地板太空虚所至，如果地面是水磨石或者铺的地板块就相对结实，如果是水泥地平，地面就很虚会引起共振，碰到这种情况如何处理呢？可以去橡胶五金店买几块黑色橡皮胶垫，厚度6-10毫米左右，大小10公分和地脚垫尺寸稍大点就行，松开地脚螺丝，把橡皮胶垫垫在水平地脚垫下面，就可以起到很大的减震功能了。

Third, if the action is done, vibration have not been eliminated, it should check whether the ground floor to empty because, if the ground is terrazzo floor block or shop is relatively strong, if it is a virtual ground cement ground will cause resonance, encountered such a situation such as how to deal with? You can go to the hardware store to buy a few pieces of black rubber rubber pad, the thickness of 6-10 mm, the size of 10 cm and foot size slightly larger point on the line, loosen the anchor bolts, the rubber pad in the horizontal foot, you can play a big damping function.

第四，如果Q420C高强板车床震动仍未消除，可以换个砂轮试试，如果是法兰没有经过效平衡块校正就把平衡块装上去了，那就拆掉平衡块装上去，不行就换个新法兰试试，一般问题就解决了。

Fourth, if the Q420C high strength plate lathe vibration have not been eliminated, can change the wheel to try, if there is no effect after correction of the balance block balance block up flange, then removed the balance block up, not to change the new flange to try, you have resolved the problem.

第五，如果进行上述一系列动作仍未能消除震动那可能就不是你能处理的范畴了，有可能是磨床主轴时间用长了本身震动，里面轴承或马达坏了，也有可能是Q420C高强板生产机床的结构及装配有问题，这时就要通知厂家来处理了。

Fifth, if the above a series of actions failed to eliminate vibration may not be that you can handle the category, there may be a long time with the spindle vibration, inside bearing or damaged motor, there may be a structure and assembly of Q420C high strength plate production machine has a problem, then we must notify the manufacturer to the treatment.

本文由济钢一级代理商为您提供，我们的网站是：http://www.jnyygt.com我们将以全心全意的热情为您提供更优质的服务，欢迎您的访问！

This paper consists of Jinan level agents to provide you, our website is: http://www.jnyygt.com we will provide higher quality service to serve the enthusiasm for you, welcome your visit!