一。环保，重要性我就不讲了，生态板顾名思义不环保叫什么生态板。目前做这行的厂家最高可控制在E0，是适合在任何情况下使用的产品。森骏牌的E0生态板，没有任何异味和刺激性气味，各项指标都能达到国家标准，真正为消费者实现上午装修，下午入住的要求。

A. Environmental protection, the importance of I do not speak, as the name suggests is not environmentally friendly ecological board. At present, do this line of manufacturers the highest control in E0, is suitable for the use of products in any case. Shouju brand E0 ecological board, without any odor and a pungent smell, the indicators can reach the national standard, for consumers to achieve truly a decoration in the morning, check the afternoon.

二。看平整。检测办法：在光线稍暗的地方45度角看长(2米44)的一面，是否有凹凸不平，看表面的三条拼接缝和砂光痕是否明显。这不是硬标准，但反应一个厂家的工艺能力。

Two. See level. Detection method: in light slightly dark place at a 45 degree angle to see long (2 44 meters) side, whether rugged, look at the surface of three spell seams and sanding marks is obvious. This is not a hard standard, but the reaction of a manufacturer's technological ability.

三。看表面是否有干花湿花家装叫碳化，如板材表面有亮晶晶的点状块状，时间长会发黑或表面出现如油漆掉色状这都是干湿花。这些都反映一下工厂工艺掌握程度，也是反映板材质量重要问题之一。

Three. Whether the watch surface has dried wet flower decoration called carbide, such as the surface of the plate to the sparkling point block, a long time will appear black or surface such as paint fade like this are wet and dry flower. These reflect the extent of the factory craft, but also reflect the quality of the important issues of sheet.

四。纸张褪色，相对来讲油墨纸更不容易褪色立体感较强，色浆纸要差的多(例如油漆和涂料之间的区别)检测办法：用两张板叠起错开在太阳底下晒几个小时后，看下面的那张板是否有色差。

Four. Faded paper, relatively speaking, paper, ink more not easy to fade, three-dimensional sense of strong, paste paper to poor (such as the difference between the paint and coatings) detection method: with two pieces of plate stack stagger in the sun drying for several hours, see below the plate is a color difference.

五。板材开裂和鼓泡是胶合强度和基材引起的肯定是质量问题没有任何理由，视角可看。

Five. Plate cracking and blister is the bonding strength and the substrate caused by the quality of the problem is no reason for any reason, the perspective can be seen.

六。看纸张是否完全固，相当于没有把饭完全煮熟。可看到表面不耐污染，用手摸起来不是很爽手有发棉的感觉，板面看起来像蒙上一层雾。最好的就是摸起来像金属的感觉最佳。检测办法：用鞋油，囗红或油笔涂在板面上几分钟后看能否完全后擦掉。

Six. To see whether the paper is completely solid, equivalent to not completely cooked rice. Can not see the surface pollution resistant, touch up is not very cool hand hair cotton feeling, looks like a surface covered with a layer of fog. The best is to feel like metal is the best. Detection methods: with his red pen or shoe polish, painted on the surface after a few minutes to see whether completely erased.

七。看装饰纸是否与木头贴牢。(这跟木工加工时有关系，锯开时会有蹦边现象，会增加加工难度和影响美观)检测办法：用强力胶在每平方分米的小块上粘住用力拉看是否把纸张拉掉。或用手在横切面上用手扣一下，能不能把最上面的纸扣掉。

Seven. See whether the decorative paper and wood. (it has a relationship with the woodworking, saws will have jumped on the edge of the phenomenon, will increase the processing difficulty and affect the appearance) detection method: use super glue on per square decimeter of small stick force pull to see whether paper yank. Or hand in cross section by hand pull, can put the top out of paper.

八。整张板的厚薄差检测办法：用卡尺在一张板上量多个点的厚度，误差在20丝属于正常，但家装要求可以放宽。

Eight. A whole piece of plate thickness difference detection method: using vernier calipers in a plate quantity point thickness, error in 20 wire is normal, but Jiezhuang requirements can be relaxed.

九。板材变形，板材变形程度也是反映厂家的工艺能力，板材的静曲强度不够。一般来讲板材在没有做成成品之前，在每包的最上面两张略有变形也属正常。做成衣柜或成品之后(不包括大面积的平开门)如有变形属质量问题。检测办法；眼睛可看。

Nine. Plate deformation, the degree of deformation of the plate is also reflected in the process capability of the manufacturers, the static bending strength of the plate is not enough. Generally speaking in the plate before the finished product, the top two in each package has a slight deformation is normal. After the wardrobe or the finished product (does not include large area of flat door) if there is a quality problem of deformation. Detection method; the eyes can see.

本文来自：济钢一级代理更多的内容请点击：http://www.jnyygt.com我们将会为您提问的问题提供一个满意的服务，欢迎您的来电！

This article from: Jinan Iron and steel group level agents more content, please click: http://www.jnyygt.com we will question you are to provide a satisfactory service, welcome your call!